Status LED
Quick Start Guide
RemoteLinc™ 2 - INSTEON® Wireless Keypad
Model: 2444A2WH8
Introduction
Conveniently control your home’s INSTEON network with the compact and
versatile RemoteLinc 2 wireless keypad controller.
8 Scene Buttons
(Tap=On/Off;
Press and
hold=dim/brighten)
What's Included
•
RemoteLinc 2
Charging LED
(inside case)
Getting Started
Fully charge RemoteLinc 2 prior to programming (or anytime the unit is not
responding) using a Type A to Micro-B USB cable (sold separately). The
red Charging LED will turn off once the battery is fully charged
(approximately one hour). Slide the power switch to the ON position.
Note: RemoteLinc 2 requires an INSTEON dual-band or RF device to
communicate with other devices on your INSTEON network.
RemoteLinc 2 uses a subtle beeper sound to assist setup. It is
recommended that you program the unit in a quiet area.
Micro-USB
Charging
Jack
Power
Switch
(Left=Off,
Right=On)
Set button
Add RemoteLinc 2 (Button) as an INSTEON Controller
1) Tap the scene button of choice on the RemoteLinc 2
2) Adjust the responder to the state you want when the scene is activated from RemoteLinc 21
3) Press and hold RemoteLinc 2's Set button until RemoteLinc 2 beeps
RemoteLinc 2 status LED will begin blinking green
4) Press and hold the responder’s Set button until the responder beeps or its LED flashes
RemoteLinc 2 will double-beep and its LED will stop blinking
Responder LED will stop blinking (it may also double-beep)
5) Confirm that scene addition was successful by tapping the programmed scene button on RemoteLinc 2
The responder will toggle between the scene’s preset on-level and off
1 If the responder is a multi-scene device such as a KeypadLinc, tap the scene button you wish to control until its LED is in the desired state (on or off)
Using RemoteLinc 2
Each scene button (a-h) controls its own scene, sending commands to devices linked specifically to that button.
Dimmable responders may behave differently, depending on whether you tap, double-tap or press and hold a
button. Non-dimming responders will only turn full-on or full-off, no matter what method you use.
Last Command Sent
Off or Dim
Tap
Press and hold
Double-tap
Brighten scene members until
released
Turn scene members full-on
instantly
Turn scene on
Turn scene members full-off
instantly
On or Bright
Turn scene off Dim scene members until released
The RemoteLinc 2 Status LED will flash green once for each on/brighten command sent and red once for each
off/dim command sent
Warning: RemoteLinc 2 is permanently sealed. Do not attempt to open case. Doing so will damage the remote
and void the warranty.
Owner’s Manual and Tech Support
Owner’s Manual and current Quick Start Guide: http://www.insteon.com/support
Call: INSTEON Support Line at 800-762-7845
2444A2xx8 Rev. 7/16/2012 12:31 PM / See Owner’s Manual for Warranty Information, Patented
© Copyright 2012, INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845
|
Iiyama Computer Monitor E1706S User Manual
JVC AV 21F24 AV 21L24 AV 21C14 AV 21D14 AV 21E14 AV 21F14 AV 21L14 AV 21T14 AV 20N14 AV 14A14 AV 14F14 User Manual
Lindy 20965 User Manual
Lucent Technologies Telephone Call Handling Back Panels_ Front Panels 4406D+ User Manual
Maverick Ventures ET 85 User Manual
Moffat Blue Seal GE56B User Manual
NEC AccuSync LCD92V User Manual
Nortel Networks SoundPoint IP 550 User Manual
Philips 17GR2340 User Manual
Philips SA1103 User Manual