DUAL DIN SIZED CD RECEIVER
DPX502U
DPX502UY
INSTRUCTION MANUAL
© B64-3829-00/00 (EW/E2W)
Safety precautions
Do Not Load 8 cm (3 in.) CDs in the CD slot
If you try to load a 8 cm (3 in.) CD with its adapter into
the unit, the adapter might separate from the CD and
damage the unit.
2WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
About CD players/disc changers connected
to this unit
• Do not watch or fix your eyes on the unit’s display
when you are driving for any extended period.
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting
and wiring work to professionals.
Kenwood disc changers/ CD players released in 1998
or later can be connected to this unit.
Refer to the catalog or consult your Kenwood dealer
for connectable models of disc changers/ CD players.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made by
other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players to
this unit may result in damage.
Set the "O-N" Switch to the "N" position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
2CAUTION
To prevent damage to the machine, take
the following precautions:
• Make sure to ground the unit to a negative 12V DC
power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• When replacing a fuse, only use a new fuse with
the prescribed rating. Using a fuse with the wrong
rating may cause your unit to malfunction.
• Use only the screws provided or specified for
installation. If you use wrong screws, you could
damage the unit.
¤
•
You can damage both your unit and the CD changer if you
connect them incorrectly.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
The "AAC" logo is trademark of Dolby
Laboratories.
|
English
3
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• The RDS feature won’t work where the service is not
supported by any broadcasting station.
• The characters which can be displayed by this unit
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ; ^ - { } |
~ .
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode Setting> (page 31).
About KENWOOD "Music Editor" of
PC application attached to DPX502U/
DPX502UY
How to reset your unit
• If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when the
Reset button is pressed.
• "Music Editor" is recorded in the CD-ROM attached
to this unit.
• Remove the USB device before pressing the Reset
button. Pressing the Reset button with the USB
device installed can damage the data contained in
the USB device. For how to remove the USB device,
refer to <Playing USB (iPod) device> (page 19).
• Press the reset button if the disc auto changer fails
to operate correctly. Normal operation should be
restored.
• Refer to the attached installation manual for the
installation method of "Music Editor".
• Refer to the user’s manual recorded in the
installation CD-ROM and Help of "Music Editor" for
the operation method of "Music Editor".
• The unit can play CD/ USB device created by "Music
Editor".
• Information about "Music Editor" upgrade is put on
Reset button
|
4
English
About Audio file
About USB device
•
Playable Audio file
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma),
WAV (.wav)
• You cannot connect a USB device via a USB hub.
•
•
•
•
Playable disc media
CD-R/RW/ROM
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• Do not directly connect the USB device to the USB
connector on the panel. Connect it using a cable.
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device
USB mass storage class, iPod with KCA-iP200
Playable USB device file system
FAT16, FAT32
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
• Leave the cap on when not using an USB device.
• For how to play the audio files recorded in a USB
device, see <CD/USB device/Audio file/External disc
control features> (page 18).
• When connecting the USB device, usage of the CA-
U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
:
Follder
Audiofile
CD
(ꢂ)
vꢀ
ꢁ
ꢃ
vꢆ
vꢇ
About DAB Tuner control
Refer to A group on the Instruction manual of DAB
Tuner KTC-9090DAB (optional accessory) for the
control method of DAB Tuner function.
However, the following control methods of the
function for this unit may be differed from the
Instruction manual; therefore, refer to the following
supplemental instruction.
ꢅ
vꢄ
ꢈ
vꢉ
v.
An online manual about audio files is put on the
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
<Auto Ensemble Memory Entry>
1. Select the preset band for Auto Ensemble Memory
Entry.
2. Press the [AME] button for at least 2 seconds.
Open Auto Ensemble Memory Entry.
After storing in the memory finishes, the number
of the pre-set buttons and the ensemble label are
displayed.
⁄
•
In this manual, the word "USB device" is used for flash
memories and digital audio players which have USB
terminals.
<Searching by programme type and language>
and <Languages to be displayed> in <Programme
Type (PTY) Function>
At the operation to press [DISP] button, use [TI]
button instead.
<Automatic Switching DAB priority>
This function cannot be used.
•
The word "iPod" appearing in this manual indicates the iPod
connected with the KCA-iP200 (optional accessory). The
iPod connected with the KCA-iP200 can be controlled from
this unit. iPods that can be connected with the KCA-iP200
are the iPod nano and the iPod with video. When an iPod
is connected using a commercially available USB cable, it is
handled as a mass-storage-class device.
•
For the supported formats and types of USB device, refer to
|
English
5
Notes
This Product is not installed by the manufacturer of a
vehicle on the production line, nor by the professional
importer of a vehicle into an EU Member State.
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
Information on Disposal of Old Electrical
and Electronic Equipment (applicable for
EU countries that have adopted separate
waste collection systems)
Products with the symbol (crossed-out
wheeled bin) cannot be disposed as
household waste.
Old electrical and electronic equipment
should be recycled at a facility capable
of handling these items and their waste
byproducts. Contact your local authority
for details in locating a recycle facility
nearest to you. Proper recycling and waste
disposal will help conserve resources whilst
preventing detrimental effects on our
health and the environment.
CDs that cannot be used
• CDs that are not round cannot be used.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
The marking of products using lasers
(Except for some areas)
.
CLASS 1
LASER PRODUCT
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not been
finalized. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
|
6
English
General features
DISP
Auxiliary input
Control knob
VOL
ATT
Q
SRC
Clock display
LOUD indicator
ATT indicator
* An equipment such as a portable audio player can
be connected to the auxiliary input terminal using a
commercially available mini-plug (3.5ø).
Power
Turning ON the Power
Press the [SRC] button.
⁄
•
This unit automatically turns full power OFF after 20
minutes lapses in Standby mode in order to save the
vehicle's battery.
The time until full power OFF can be set in <Power OFF
Timer> (page 30).
⁄
•
When the power is ON, the <Security Code> (page 25) is
displayed as "CODE ON" or "CODE OFF".
Turning OFF the Power
•
•
•
When connection of the iPod is recognized, the source
display changes from "USB" to "iPod".
USB (iPod) source is recognized as CD source on the
connected unit.
Use the mini-plug which is stereo type and does not
have any resistance.
Press the [SRC] button for at least 1 second.
Selecting the Source
Press the [SRC] button.
Source required
Display
Tuner
USB device (iPod)
CD
"TUNER"
"USB" ("iPod")
"CD"
External disc (Optional accessory)
Auxiliary input*
"CD CH"
"AUX"
Auxiliary input (Optional accessory)
Standby (Illumination only mode)
"AUX EXT"
"STANDBY"
|
English
7
General features
Volume
Audio Control
Increasing Volume
Turn the [VOL] knob clockwise.
1 Select the source to adjust
Press the [SRC] button.
Decreasing Volume
Turn the [VOL] knob counterclockwise.
2 Enter Audio Control mode
Press the [VOL] knob.
3 Select the Basic Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
Attenuator
Turning the volume down quickly.
Press the [ATT] button.
Each time you press the button, the Attenuator
turns ON and OFF.
When the Attenuator is ON, the "ATT" indicator
blinks.
4 Adjust the Basic Audio item
Turn the [VOL] knob.
Adjustment Item Display
Range
Rear Volume
Subwoofer level
Bass level*
Middle level*
Treble level*
Balance
"R-VOL"
"SW L"
"BAS L"
"MID L"
"TRE L"
"BAL"
0 — 35
–15 — +15
–8 — +8
–8 — +8
–8 — +8
System Q
Left 15 — Right 15
Rear 15 — Front 15
Selecting the best sound setting preset for different
types of music.
Fader
"FAD"
Exit Audio Control mode (Volume control mode)
1 Select the source to set
* You can adjust these items in detail. Refer to <Adjusting
the detail of Audio Control> (Page9).
* Source tone memory: Puts the set up value in the
memory per source. (Detail Audio item is included)
Press the [SRC] button.
2 Select the Sound type
Press the [Q] button.
5 Exit Audio Control mode
Press any button.
Press a button other than the [VOL] knob and [ATT]
When you press the button once, the current
sound setting is displayed.
Each time you press the button, the sound setting
alternates.
button.
Sound setting
User memory
Rock
Pops
Easy
Display
"USER"
"ROCK"
"POPS"
"EASY"
Top 40
Jazz
"TOP40"
"JAZZ"
Natural
"NATURAL"
⁄
•
User memory: The values set on the <Audio Control>
(page 8).
•
Change each setting value with the <Speaker Setting>
(page 10).
First, select the speaker type with the Speaker setting.
|
8
English
Adjusting the detail of Audio Control
Among the Basic Audio items, you can adjust the Bass
level, Middle level, and Treble level in detail.
⁄
•
When you set the Bass Extend to ON, low frequency
response is extended by 20%.
•
You can exit the Audio Control mode at anytime by
pressing any button except for [VOL] knob and [ATT]
button.
1 Select the Basic Audio item
Select the desired item to be set in detail from
followings;
• Bass level
• Middle level
• Treble level
For how to select Basic Audio items, see <Audio
Control> (page 8).
2 Enter Detail adjustment mode of Audio
Control
Press the [VOL] knob for at least 1 second.
3 Select the Detail Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
4 Adjust the Detail Audio item
Turn the [VOL] knob.
Bass level
Adjustment Item
Display
Range
Bass Center Frequency
"BAS F"
40/50/60/70/80/100/
120/150 Hz
Bass Q Factor
Bass Extend
"BAS Q"
"B EX"
1.00/1.25/1.50/2.00
OFF/ON
Middle level
Adjustment Item
Display
Range
Middle Center Frequency "MID F"
0.5/1.0/1.5/2.0 kHz
1.0/2.0
Middle Q Factor
"MID Q"
Treble level
Adjustment Item
Display
Range
Treble Center Frequency "TRE"
10.0/12.5/15.0/17.5 kHz
5 Exit the Detail Audio Control mode
Press the [VOL] knob for at least 1 second.
|
English
9
General features
Audio Setup
Speaker Setting
Setting the Sound system, such as Cross over
Network.
Fine-tuning so that the System Q value is optimal
when setting the speaker type.
1 Select the source to adjust
1 Enter Standby
Press the [SRC] button.
Press the [SRC] button.
Select the "STANDBY" display.
2 Enter Audio Setup mode
Press the [VOL] knob for at least 1 second.
2 Enter Speaker Setting mode
Press the [VOL] knob.
3 Select the Audio Setup item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
3 Select the Speaker type
Turn the [VOL] knob.
Each time you turn the knob, the setting alternates
between the settings shown in the table below.
4 Setup the Audio item
Speaker type
OFF
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
Display
Turn the [VOL] knob.
"SP OFF"
"SP 5/4"
"SP 6*9/6"
"SP OEM"
Adjustment Item
Display
Range
Through/40/60/80/100/120/
150/180/220 Hz
Front High Pass Filter "HPF"
Rear High Pass Filter "HPR"
Through/40/60/80/100/120/
150/180/220 Hz
50/60/80/100/120/Through Hz
Reverse (180°)/ Normal (0°)
–8 — 0 (AUX: -8— +8)
OFF/ON
4 Exit Speaker Setting mode
Press the [VOL] knob.
Low Pass Filter
Subwoofer Phase
Volume offset
Loudness
"LPF"
"PHAS"
"V-OFF"
"LOUD"
"2ZON"
Subwoofer Output
Turning the Subwoofer output ON or OFF.
Dual Zone System
OFF/ON
⁄
Push the Control knob toward down for at least
2 seconds.
Each time you push the knob, Subwoofer output
switches ON and OFF.
When it is ON, "SW ON" is displayed.
•
Volume offset: Sets each source’s volume as a difference
from the basic volume.
•
Loudness: Compensates for low and high tones
during low volume. (Only the low tone is
compensated for when the tuner is selected
as a source.)
•
Dual Zone System
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by <Dual Zone
System Setting> (page 27).
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by [VOL] knob.
- Adjust the volume of Rear channel by <Audio Control>
(page 8).
- The Audio Control has no effect on sub source.
You can use the Dual Zone System with the internal
auxiliary input.
•
5 Exit Audio Setup mode
Press the [VOL] knob for at least 1 second.
|
10
English
TEL Mute
The audio system automatically mutes when a call
comes in.
When a call comes in
"CALL" is displayed.
The audio system pauses.
Listening to the audio during a call
Press the [SRC] button.
The "CALL" display disappears and the audio system
comes back ON.
When the call ends
Hang up the phone.
The "CALL" display disappears and the audio system
comes back ON.
⁄
•
To use the TEL Mute feature, you need to hook up
the MUTE wire to your telephone using a commercial
telephone accessory. Refer to <Connecting Wires to
Terminals> (page 35).
|
English
11
General features
•
* When playing music from iPod or music edited by
"Music Editor", the folder name display may show
something different such as playlist or artist name
depending on the music selection procedure.
Switching Display
Changing the information displayed.
Press the [DISP] button.
Each time the button is pressed the display
switches as shown below.
In Tuner source
Information
Display
Program Service name or Frequency
(FM)
"FREQ/PS"
Radio text, Program Service name or
Frequency (FM)
"R-TEXT"
Frequency (MW, LW)
Clock
"FREQ"
"CLOCK"
In CD & External disc source
Information
Disc title
Track title
Track number & Play time
Clock
Display
"D-TITLE"
"T-TITLE"
"P-TIME"
"CLOCK"
In Audio file source
Information
Display
"TITLE"
"ALBUM"
"FOLDER"
"FILE"
Music title & Artist name
Album name & Artist name
Folder name*
File name
Play time & Music number
Clock
"P-TIME"
"CLOCK"
In Standby/ Auxiliary input source
Information
Source name
Clock
Display
"SRC NAME"
"CLOCK"
⁄
•
•
•
•
•
When LX-AMP is connected, the item setup by the
Display mode of LX-AMP is displayed.
When the music number exceeds 1000, only the last 3
digits of its number are displayed.
When you select the clock display, the display setting of
each source will be changed to the clock display.
Music title, Artist name, and Album name cannot be
displayed in WAV file.
If the selected display item does not have any
information, alternative information is displayed.
|
12
English
Tuner features
FM
AM
Control knob
AME
SRC
1 - 6
Frequency display
Band display
ST indicator
Preset station number
Tuning
Selecting the station.
1 Select tuner source
Press the [SRC] button.
Select the "TUNER" display.
2 Select the band
Push the Control knob towards [FM] or [AM].
Each time you push the knob toward [FM], it
switches between the FM1, FM2, and FM3 bands.
3 Tune up or down band
Push the Control knob towards [4] or [¢].
⁄
•
During reception of stereo stations the "ST" indicator is
ON.
|
English
13
Tuner features
Function of remote control
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
Direct Access Tuning
Entering the frequency and tuning.
1 Select the band for Auto Memory Entry
1 Select the band
Push the Control knob towards [FM] or [AM].
Press the [FM] or [AM] button.
2 Open Auto Memory Entry
2 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Press the [AME] button for at least 2 seconds.
"A-MEMORY" is displayed.
When 6 stations that can be received are put in the
memory Auto Memory Entry closes.
"– – – –" is displayed.
3 Enter the frequency
⁄
Press the number buttons on the remote
•
When the <AF (Alternative Frequency)> (page 28) is ON,
only RDS stations are put in the memory.
When Auto Memory Entry is done in the FM2 band, the
RDS stations preset in the FM1 band are not put in the
memory.
control.
Example:
Desired frequency
92.1 MHz (FM)
810 kHz (AM)
•
Press button
[0], [9], [2], [1]
[0], [8], [1], [0]
Likewise, when Auto Memory Entry is done in the FM3
band, RDS stations preset in FM1 or FM2 are not put in
the memory.
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
⁄
Preset Tuning
Recalling the stations in the memory.
•
You can enter the FM band frequency in steps of a
minimum of 0.1 MHz.
1 Select the band
Push the Control knob towards [FM] or [AM].
Station Preset Memory
Putting a station in the memory.
2 Recall the station
Press the desired [1] — [6] button.
1 Select the band
Push the Control knob towards [FM] or [AM].
2 Select the frequency to put in the memory
Push the Control knob towards [4] or [¢].
3 Put the frequency in the memory
Press the desired [1] — [6] button for at least 2
seconds.
The preset number display blinks 1 time.
On each band, 1 station can be put in the memory
on each [1] — [6] button.
|
14
English
RDS features
Control knob
TI
SRC
1 - 6
Radio text
TI indicator
PTY indicator
RDS indicator
Receiving other traffic information stations
Push the Control knob towards [4] or [¢].
Traffic Information
Changing to traffic information automatically when
a traffic bulletin starts even when you are not
listening to the radio.
⁄
•
Traffic information can be switched when it is on the
Tuner Source. However, you cannot switch the Traffic
information during reception of the Traffic bulletin
switched from the source other than the Tuner.
Press the [TI] button.
Each time you press the button, the Traffic
information function turns ON and OFF.
When traffic information is ON, "TI" indicator is ON.
When a traffic information station is not being
received the "TI" indicator blinks.
Radio Text Scroll
Scrolling the displayed radio text.
When a traffic bulletin starts, "TRAFFIC" is displayed
and the audio changes to traffic information.
Push the Control knob toward up for at least 2
seconds.
⁄
•
During reception of an AM station when the Traffic
Information function is turned ON, the frequency
changes to an FM station.
⁄
•
When the <Display Illumination Control> (page 26) is set
to OFF, the display may black out while scrolling.
•
During reception of traffic information the adjusted
volume is automatically remembered, and the next time
the audio changes to traffic information, the volume
automatically becomes the remembered volume.
|
English
15
RDS features
PTY (Program Type)
Selecting the Program Type and searching for a
station.
⁄
•
Speech and Music include the Program type shown
below.
Music: No.12 — 17, 26 — 30
Speech: No.3 — 11, 18 — 25, 31
1 Enter PTY mode
•
•
You can put the Program Type in the [1] — [6] button
memory and for quick recall. Refer to the <Program Type
preset> (page 16).
You can change the display language. Refer to
<Changing Language for PTY Function> (page 17).
Press the Control knob.
During PTY mode the "PTY" indicator is ON.
⁄
•
This function cannot be used during a traffic bulletin or
AM reception.
3 Search for the selected Program Type station
Push the Control knob towards [4] or [¢].
When you want to search for other stations, push
[4] or [¢] of the Control knob again.
2 Select the Program Type
Push the Control knob towards up or down.
Each time you push the knob, the Program Type
alternates between program types shown in the
table below.
⁄
•
When the selected Program Type is not found, "NO PTY"
is displayed. Select another Program Type.
No.
1.
Program Type
Speech
Display
"SPEECH"
"MUSIC"
4 Exit PTY mode
2.
Music
Press the Control knob.
3.
News
"NEWS"
4.
5.
6.
Current Affairs
Information
Sport
"AFFAIRS"
"INFO"
"SPORT"
Program Type preset
Putting the Program Type in the Preset button
memory and quick recall.
7.
8.
9.
Education
Drama
Culture
Science
Varied
Pop Music
Rock Music
Easy Listening Music
Light Classical
Serious Classical
Other Music
Weather
"EDUCATE"
"DRAMA"
"CULTURE"
"SCIENCE"
"VARIED"
"POP M"
"ROCK M"
"EASY M"
"LIGHT M"
"CLASSICS"
"OTHER M"
"WEATHER"
"FINANCE"
"CHILDREN"
"SOCIAL"
"RELIGION"
"PHONE IN"
"TRAVEL"
"LEISURE"
"JAZZ"
"COUNTRY"
"NATION M"
"OLDIES"
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
Presetting the Program Type
1 Select the Program Type to preset
Refer to <PTY (Program Type)> (page 16).
2 Preset the Program Type
Press the desired [1] — [6] button for at least 2
seconds.
Recalling the preset Program Type
Finance
1 Enter PTY mode
Children’s programs
Social Affairs
Religion
Phone In
Travel
Refer to <PTY (Program Type)> (page 16).
2 Recall the Program Type
Press the desired [1] — [6] button.
Leisure
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
"FOLK M"
"DOCUMENT"
|
16
English
Changing Language for PTY Function
Selecting the Program Type display language.
1 Enter PTY mode
Refer to <PTY (Program Type)> (page 16).
2 Enter Changing Language mode
Press the [TI] button.
3 Select the language
Push the Control knob towards up or down.
Each time you push the knob, the language
alternates between the languages shown in the
table below.
Language
English
French
Swedish
German
Display
"ENGLISH"
"FRENCH"
"SWEDISH"
"GERMAN"
4 Exit Changing Language mode
Press the [TI] button.
|
English
17
CD/USB device/Audio file/External disc control features
Control knob
USB connector
SRC
S.MODE SCAN RDM/3/ REP F.SEL M.RDM
A.RDM
Track number
Play time
IN indicator
Disc number
Playing CD & Audio file
USB Device Connection
1 Remove the cap and connect the
When a disc is inserted
Press the [SRC] button.
Select the "CD" display.
USB cable.
2 Connect the USB device to the unit
using the USB cable.
⁄
•
When a CD is inserted, the "IN" indicator is ON.
Pause and play
Press the Control knob.
Each time you press the knob, the audio pauses or
plays.
Eject the CD
Press the [0] button.
⁄
•
•
•
For the audio files and discs you can play with this unit,
refer to <About Audio file> (page 5).
You can play the file made by KENWOOD Music Editor by
the same operation.
You can eject the disc for 10 minutes after switching off
the engine.
•
When connecting the USB device, usage of the CA-U1EX
(option) is recommended.
|
18
English
Playing USB (iPod) device
Drive Search
Selecting the device inserted in the Multi Card
Reader.
When the USB device is not connected
Connect the USB device
Playback of the file contained in the USB device
starts.
1 Put the playback to pause
Press the [S.MODE] button.
2 Select a device
When the USB device is connected
Push the Control knob towards up or down.
Select USB source
Press the [SRC] button.
Select the "USB" (or "iPod") display.
3 Restart playback
Press the [S.MODE] button.
⁄
⁄
•
This unit is compliant with Multi Card Readers with a
maximum of 4 slots.
•
•
•
For the audio files that can be played with this unit and
the devices that can be connected to this unit, refer to
<About Audio file> (page 5).
•
If a device is inserted during connection of the Multi
Card Reader, it is not recognized. Select the Remove
mode with reference to <Playing USB (iPod) device>
(page 19), remove the Card Reader, and then insert the
memory.
The word "iPod" appearing in this manual indicates the
iPod connected with the KCA-iP200 (optional accessory).
Refer to <About Audio file> (page 5).
If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, "RESUMING" is displayed without displaying
a folder name, etc. Changing the browse item will
display a correct title, etc.
•
When the iPod is connected to this unit, "KENWOOD" or
"✓" is displayed on the iPod to indicate that you cannot
operate the iPod.
•
•
•
When the USB device is connected to this unit, it can be
charged up provided that this unit is powered.
When the Multi Card Reader is used, refer to <Drive
Search> (page 19).
After you stopped playing a file contained in the USB
device, you can restart playing the file from the point
where you stopped its playback.
Even after removing the USB device, you can restart
playing the file from the point where you stopped its
playback as long as the files contained in the USB device
are all the same.
•
•
Be sure to insert the USB device connector as far as it will
go.
You can play the file made by KENWOOD Music Editor by
the same operation.
Pause and play
Press the Control knob.
Each time you press the knob, the audio pauses or
plays.
Removing the USB device
1 Set the remove mode as the USB source
Press the [0] button for at least 2 seconds.
"REMOVE" display blinks.
2 Remove the USB device.
|
English
19
CD/USB device/Audio file/External disc control features
Function of disc changer/ Audio file
Playing External Disc
Playing discs set in the optional accessory disc
Disc Search/Folder/Album Search
player connected to this unit.
Switching between folders/albums contained in
the disc in the disc changer, media, or device being
played now.
Press the [SRC] button.
Select the display for the disc player you want.
Display examples:
Push the Control knob towards up or down.
Display
"CD CH"
"MD CH"
Disc player
CD changer
MD changer
Function of remote control
Direct Music Search
Pause and play
Press the Control knob.
Doing Music Search by entering the music number.
Each time you press the knob, the audio pauses or
plays.
1 Enter the music number
Press the number buttons on the remote
control.
⁄
•
•
Disc 10 is displayed as "0".
⁄
The functions that can be used and the information that
can be displayed will differ depending on the external
disc players being connected.
•
You can select Direct music Search up to 999.
2 Do music Search
Press the [4] or [¢] button.
Cancelling Direct Music Search
Press the [38] button.
Fast Forwarding and Reversing
⁄
Fast Forwarding
Hold down toward [¢] with the Control knob.
Release to resume the playback.
•
This function is not available on iPod and the music
edited by "Music Editor".
Reversing
Hold down toward [4] with the Control knob.
Function of disc changers with remote control
Release to resume the playback.
Direct Disc Search
Doing Disc Search by entering the disc number.
⁄
•
•
There is no sound while the Audio file is being searched.
The accurate play time is not displayed during fast
forwarding or reversing of the Audio file.
1 Enter the disc number
Press the number buttons on the remote
control.
2 Do Disc Search
Music Search
Press the [+] or [–] button.
Switching between music contained in the disc or
folder being played now.
Cancelling Direct Disc Search
Press the [38] button.
Push the Control knob towards [4] or [¢].
⁄
•
Input "0" to select disc 10.
|
20
English
Track/File/Disc/Folder Repeat
Random Play
Replaying the music, disc in the Disc changer or
Audio file folder you are listening to.
Play all the music on the disc or Audio file folder in
random order.
Press the [REP] button.
Press the [RDM] button.
Each time you press the button, the Repeat Play
alternates between the modes shown in the tables
below.
Each time you press the button, Random Play turns
ON or OFF.
When the Random mode is ON, "DISC RDM"/"FOLD
RDM"/"RDM ON" is displayed.
In CD & External disc source
⁄
Repeat play
Track Repeat
Disc Repeat (In Disc Changer)
OFF
Display
•
When you push the Control knob toward [¢], the next
"TRAC REP"
"DISC REP"
"REP OFF"
selected music starts.
In Audio file source
Function of disc changer
Magazine Random Play
Play the music on all the discs in the disc changer in
random order.
Repeat play
File Repeat
Folder Repeat*
OFF
Display
"FILE REP"
"FOLD REP"
"REP OFF"
Press the [M.RDM] button.
Each time you press the button, the Magazine
Random Play turns ON or OFF.
⁄
•
* This function is not available on iPod and the music
When the Magazine Random mode is ON, "MGZN
RDM" is displayed.
edited by "Music Editor".
⁄
•
When you push the Control knob toward [¢], the next
Scan Play
Playing the first part of each music on the disc or
Audio file folder you are listening to and searching
for the music you want to hear.
selected music starts.
1 Start Scan Play
Press the [SCAN] button.
"TRAC SCN"/"FILE SCN"/"SCAN ON" is displayed.
2 Release it when the music you want to listen
to is played
Press the [SCAN] button.
⁄
•
This function is not available on iPod and the music
edited by "Music Editor".
|
English
21
CD/USB device/Audio file/External disc control features
Function of Audio file
Function of non-iPod and non-"Music Editor" file
All Random Play
File Select 1 mode
Playing randomly from all of the Audio files
recorded in the media.
Select the target folder by tracing the hierarchical
levels of folders. This is convenient when managing
audio files by folder.
Press the [A.RDM] button for at least 1 second.
When the random mode is ON, "ALL RDM" is
displayed.
1 Enter File Select 1 mode
Press the [F.SEL] button.
Select the "F-SEL1" display.
Folder name display
Cancelling the All Random Play
Press the [A.RDM] button.
Displays the current folder name.
⁄
•
When you push the Control knob toward [¢], the next
selected music starts.
•
This function is not available on iPod and the music
edited by "Music Editor".
2 Select the folder
Operation type
Operation
Function of iPod, "Music Editor" file
Movement between folders Push the Control knob towards right or left.
Selection of folder Push the Control knob towards up.
Return to previous folder Push the Control knob towards down.
Return to root folder Press the [3] button.
File select
Selecting the music you want to listen to from the
device or media being played now.
1 Enter File Select mode
Press the [F.SEL] button.
Select the "F-SEL" display.
Select the folder containing the music you want to
listen to.
3 Determine the folder
2 Search for a music
Press the Control knob.
Select the category item using the Control
knob.
The music in the determined folder are displayed.
4 Select the music you want to listen to
Operation type
Operation
Operation type
Operation
Movement between Push the Control knob towards right or left.
items
Movement between music Push the Control knob towards right or left.
Return to folder selection Press the Control knob for at least 1 second.
step
Selection of item
Return to previous item Push the Control knob for at least 1 second.
Return to first item Press the [3] button.
Press the Control knob.
Return to root folder
Press the [3] button.
5 Play the selected music
Names of all the music are displayed in "SONGS" in
the audio file.
Press the Control knob.
Selecting a music will play it from the beginning.
Scrolling the file/folder name display
Push the Control knob toward up for at least 2
seconds.
Cancelling File Select
Press the [F.SEL] button.
Cancelling File Select 1
Press the [F.SEL] button twice.
|
22
English
Function of non-iPod and non-"Music Editor" file
Text/Title Scroll
Scrolling the displayed CD text, Audio file text, or
MD title.
File Select 2 mode
Select the target folder within the folders
containing audio files. The folder which contains
playable audio files is only displayed.
Push the Control knob toward up for at least 2
seconds.
⁄
1 Enter File Select 2 mode
Press the [F.SEL] button twice.
Select the "F-SEL2" display.
Folder name display
•
When the <Display Illumination Control> (page 26) is set
to OFF, the display may black out while scrolling.
Displays the current folder name.
2 Select the folder
Push the Control knob towards right or left.
Each time you push the knob, the folders
containing audio files are displayed one after
another.
Check the name of upper level folder
Push the Control knob towards up.
Each time you push the knob towards up, the
folder just above the current folder is displayed.
Each time you push the knob towards down, the
folder just below the current folder is displayed.
"
" is displayed while the upper level folder is
displayed.
3 Determine the folder
Press the Control knob.
The music in the determined folder are displayed.
4 Select the music you want to listen to
Operation type
Operation
Movement between music Push the Control knob towards right or left.
Return to folder selection Press the Control knob for at least 1 second.
step
5 Play the selected music
Press the Control knob.
Scrolling the file/folder name display
Push the Control knob toward up for at least 2
seconds.
Cancelling File Select 2
Press the [F.SEL] button.
|
English
23
Menu system
Control knob
SRC
MENU
Menu display
NEWS indicator
RDS indicator
Menu System
Setting beep sound during operation, etc.
functions.
The Menu system basic operation method is
explained here. The reference for the Menu items
and their setting content is after this operation
explanation.
4 Exit Menu mode
Press the [MENU] button.
⁄
•
When other items those applicable to the basic
operation method above are displayed, their setting
content chart is entered. (Normally the setting listed at
the top of the chart is the original setting.)
Also, the explanation for items that are not applicable
(<Manual Clock Adjustment> etc.) are entered step by
step.
1 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
2 Select the menu item
Push the Control knob towards up or down.
Example: When you want to set the beep sound
select the "BEEP" display.
3 Set the menu item
Push the Control knob towards right or left.
Example: When you select "BEEP", each time you
push the knob it alternates between
"BEEP ON" or "BEEP OFF". Select 1 of them
as the setting.
You can continue by returning to step 2 and
setting other items.
|
24
English
In Standby mode
Resetting the Security Code function when the
audio unit is first used after removed from the
battery power source or the Reset button is
pressed
Security Code
Activating the Security Code disables the usage
of audio unit by someone else. Once the Security
Code is activated, the entry of authorized Security
Code is required to turn on the audio unit when it is
removed from the vehicle. Indication of this Security
Code activation prevents your precious audio unit
from stealing.
1 Turn the power ON.
2 Do the step 4 through 7 step operation, and
reenter the security code.
"APPROVED" is displayed.
Now, you can use the unit.
⁄
⁄
•
If an incorrect code is entered, "WAITING" is displayed,
and the input prohibition periods shown in the table
below is generated.
•
When you activate the Security Code function, it cannot be
released.
Note, your Security Code is the 4 digit number entered in
your "Car Audio Passport" in this package.
After the input prohibition time lapses, "CODE" is
displayed, and you can reenter the code.
1 Enter Standby
Number of times the
incorrect code was input
1
2
3
4
Input prohibited time
Press the [SRC] button.
Select the "STANDBY" display.
—
5 minutes
1 hour
2 Enter Menu mode
Press the [MENU] button for at least 1 second.
When "MENU" is displayed, "CODE SET" is also
displayed.
24 hours
3 Enter Security Code mode
Press the Control knob for at least 1 second.
When "ENTER" is displayed, "CODE" is also
displayed.
In Standby mode
Touch Sensor Tone
Setting the operation check sound (beep sound)
ON/OFF.
4 Select the digits to enter
Push the Control knob towards right or left.
5 Select the Security Code numbers
Display
"BEEP ON"
"BEEP OFF"
Setting
Beep is heard.
Beep canceled.
Push the Control knob towards up or down.
6 Repeat step 4 and 5, and complete the Security
Code.
7 Confirm the Security Code
Press the Control knob for at least 3 seconds.
When "RE-ENTER" is displayed, "CODE" is also
displayed.
8 Do the step 4 through 7 step operation, and
reenter the security code.
"APPROVED" is displayed.
The Security Code function activates.
⁄
•
If you enter a Code different from your Security Code,
you have to start over from step 4.
9 Exit Security Code mode
Press the [MENU] button.
|
English
25
Menu system
In Standby mode
Display Illumination Control
This function turns off the display when you
perform no operation for 5 seconds. This function is
effective when you are driving at night.
Manual Clock Adjustment
⁄
•
You can do this adjustment when the <Synchronize Clock>
(page 26) is set as OFF.
Display
Setting
1 Select Clock Adjustment mode
Push the Control knob towards up or down.
Select the "CLK ADJ" display.
"DISP ON"
Keeps the display on.
Turns off the display when you perform no
operation for 5 seconds.
"DISP OFF"
2 Enter Clock Adjust mode
⁄
Press the Control knob for at least 1 second.
The clock display blinks.
•
•
•
Set the Display Illumination Control when the
<Demonstration mode Setting> (page 31) is set to OFF.
When the display is off, pressing any key will turn on the
display.
When the display is off, you cannot perform any
operation except for the following:
3 Adjust the hours
Push the Control knob towards up or down.
Adjust the minutes
Push the Control knob towards right or left.
•
•
•
•
•
•
Volume
Attenuator
Selecting the source
Ejecting the disc
Turning off the power
USB remove mode
4 Exit Clock adjustment mode
Press the [MENU] button.
•
During function control, such as the Menu System, the
display stays on.
In Standby mode
Synchronize Clock
Synchronizing the RDS station time data and this
unit’s clock.
In Standby mode
Dimmer
Display
"SYNC ON"
"SYNC OFF"
Setting
Synchronizes the time.
Adjust the time manually.
Dimming this unit’s display automatically when the
vehicle light switch is turned ON.
⁄
Display
"DIM AUTO"
"DIM OFF"
Setting
The display dims.
The display doesn’t dim.
•
It takes 3 to 4 minutes to synchronize the clock.
In Standby mode
Switching preout
Alternating the preout between the rear and
subwoofer. (With the subwoofer the sound outputs
without being effected by fader control.)
Display
Setting
"SWPRE R"
"SWPRE SW"
Rear preout.
Subwoofer preout.
|
26
English
In Standby mode
When LX AMP unit connecting
Built-in Amp Setting
AMP Control
Controlling the built-in amplifier.
Turning OFF this control enhances the preout
quality.
You can control the LX AMP connected to the unit.
1 Select AMP Control mode
Push the Control knob towards up or down.
Select the "AMP CTRL" display.
Display
Setting
"AMP ON"
"AMP OFF"
The built-in amplifier activates.
The built-in amplifier deactivates.
2 Enter AMP Control mode
Press the Control knob for at least 1 second.
3 Select the AMP Control item for adjustment
Push the Control knob towards up or down.
Other than Standby mode/
⁄
When the Dual Zone System is ON
•
For the details on the AMP Control item, see the
Instruction manual attached to the LX AMP.
Dual Zone System Setting
Setting the Front channel and Rear channel sound
in the Dual Zone System.
4 Adjust the AMP Control item
Push the Control knob towards right or left.
Display
"ZONE2 R"
Setting
5 Exit AMP Control mode
Sub source (Auxiliary input source) is to be rear
channel.
Sub source (Auxiliary input source) is to be front
channel.
Press the [MENU] button.
⁄
"ZONE2 F"
•
You cannot use the LX AMP operation during standby
mode.
In Audio file source
Supreme Setting
When AAC, MP3 or WMA files encoded at a low bit
rate (less than 96kbps (fs=44.1k, 48kHz)) are played,
this function restores their high frequency region
to approach the sound quality of equivalents of
these files encoded at a high bit rate. Processing is
optimized for the compression format used (AAC,
MP3, or WMA), and adjustment is made for the bit
rate used.
Display
Setting
"SPRM ON"
Plays sound using the Supreme function.
"SPRM OFF"
Plays the original sound stored in the audio file.
⁄
•
The sound effect may be imperceptible depending
on the relationship between the audio file format and
setting.
•
This function is not available on the iPod.
|
English
27
Menu system
Other than Standby mode
In Tuner mode
News Bulletin with Timeout Setting
Tuning Mode
The tuner automatically changes when a news
bulletin starts even if the radio is not being listened
to. Also, you can set the time interval when
interruption is prohibited.
Sets the tuning mode.
Tuning mode
Auto seek
Display
"AUTO 1"
Operation
Automatic search for a station.
Search in order of the stations in
the Preset memory.
Preset station seek "AUTO 2"
Display and Setting
"NEWS OFF"
Manual
"MANUAL" Normal manual tuning control.
"NEWS 00M"
"NEWS 90M"
AF (Alternative Frequency)
When you set "NEWS 00M" — "NEWS 90M", the
News Bulletin Interrupt function is ON.
When the News Bulletin is ON, the "NEWS"
indicator is ON.
When the news bulletin starts, "NEWS" is displayed,
and the tuner changes to the news bulletin.
When the reception is poor, automatically alternate
to another frequency broadcasting the same
program in the same RDS network with better
reception.
Display
"AF ON"
"AF OFF"
Setting
The AF function is ON.
The AF function is OFF.
⁄
•
If you choose the "20M" setting, further news bulletins
will not be received for 20 minutes once the first news
bulletin is received.
When the AF function is ON, the "RDS" indicator
is ON.
•
•
The news bulletin volume is the same level that was set
for <Traffic Information> (page 15).
This news bulletin function is only available if the desired
station sends PTY-code for news bulletin or belongs to
<Enhanced Other Network>-Network sending PTY-code
for news bulletin.
⁄
•
When no other stations with stronger reception are
available for the same program in the RDS network, you
may hear the incoming broadcast in bits and snatches.
Turn OFF the AF function in such a case.
•
When the News Bulletin Interrupt function is ON, the
tuner changes to an FM station.
Restricting RDS Region (Region
Restrict Function)
You can choose whether or not to restrict the
RDS channels, received with the AF function for a
particular network, to a specific region.
In Tuner mode
Local Seek
Only stations whose reception is good are searched
in auto seek tuning.
Display
Setting
Display
Setting
"LO.S OFF"
"LO.S ON"
The local seek function is OFF.
The local seek function is ON.
"REG ON"
"REG OFF"
The Region Restrict Function is ON.
The Region Restrict Function is OFF.
⁄
•
If AF function is not restricted to the specified region and
network, the AF function sets up to search the station
with good reception in the same RDS network.
|
28
English
• "GAME"
• "VIDEO"
• "TV"
Auto TP Seek
When the TI function is ON and the reception is
poor while listening to a traffic information station,
another traffic information station with better
reception will be searched for automatically.
6 Exit Auxiliary input display setting mode
Press the [MENU] button.
⁄
Display
"ATPS ON"
"ATPS OFF"
Setting
The Auto TP Seek Function is ON.
The Auto TP Seek Function is OFF.
•
When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
•
You can only set the Auxiliary input display when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used.
In FM reception
Monaural Reception
You can reduce the noise when stereo broadcasts
are received as monaural.
Function of DPX502UY
In Standby mode
Selecting Russian Characters
Display
Setting
"MONO OFF"
"MONO ON"
The monaural reception is OFF.
The monaural reception is ON.
Setting up the display of Russian characters and
undistinguishable English characters.
Display
Setting
"RUS ON"
"RUS OFF"
Displays texts using Russian characters.
Displays texts using European characters.
Auxiliary Input Display Setting
Selecting the display when changing to Auxiliary
input source.
⁄
•
Texts displayed using Russian characters are as follows.
- Folder name/ File name/ Music title/ Artist name/
Album name
- CD text (internal CD source)
Texts cannot distinguish upper case and lower case in
Russian characters.
1 Select Auxiliary input source
Press the [SRC] button.
Select the "AUX"/"AUX EXT" display.
•
2 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
3 Select Auxiliary input display setting mode
Push the Control knob towards up or down.
Select the "NAME SET" display.
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
5 Select the Auxiliary input display
Push the Control knob towards right or left.
Each time you push the knob, the display alternates
as listed below.
• "AUX"/"AUX EXT"
• "DVD"
• "PORTABLE"
|
English
29
Menu system
In Standby mode
Text Scroll
Setting the displayed text scroll.
CD Read Setting
When there is a problem with playing a CD with
special format, this setting plays the CD by force.
Display
"SCL MANU"
"SCL AUTO"
Setting
Doesn’t scroll.
Scrolls when the display changes.
Display
Setting
"CD READ1"
"CD READ2"
Play CD and Audio file.
Play CD by force.
⁄
•
The text scrolled is listed below.
- CD text
⁄
- Folder name/ File name/ Music title/ Artist name/
Album name
- MD title
•
Some music CDs may not play even in the "CD READ2"
mode.
- Radio text
Other than Standby mode
Audio Preset Memory
In Standby mode
Registering the value setup by Sound Control. The
memory cannot be erased by the Reset button.
Built-in Auxiliary input Setting
Set the Built-in Auxiliary Input function.
1 Setup Sound Control
Refer to the following operations to setup the
Sound Control.
Display
"AUX OFF" When selecting the source there’s no Auxiliary Input.
"AUX ON" When selecting the source there’s Auxiliary Input.
Setting
- <Audio Control> (page 8)
- <Audio Setup> (page 10)
2 Enter Menu mode
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
In Standby mode
Power OFF Timer
3 Select Audio Preset mode
Setting the timer to turn this unit’s power OFF
automatically when Standby mode continues.
Using this setting can save the vehicle’s battery
power.
Push the Control knob towards up or down.
Select the "A-PRESET" display.
4 Enter Audio Preset mode
Press the Control knob for at least 1 second.
Display
Setting
5 Select the Audio Preset Memory
Push the Control knob towards up or down.
Select the "MEMORY" display.
"OFF – – –"
Power OFF Timer function is OFF.
"OFF 20M"
(Original setting)
Turns the power OFF after 20 minutes.
"OFF 40M"
"OFF 60M"
Turns the power OFF after 40 minutes.
Turns the power OFF after 60 minutes.
6 Put the Audio Preset in the memory
Press the Control knob for at least 2 seconds.
The "MEMORY" display blinks 1 time.
7 Exit Audio Preset mode
Press the [MENU] button.
⁄
•
Register 1 pair of Audio Preset Memory. You cannot
register by the source.
•
When you press the Reset, all the sources will be the
setting value which is registered.
|
30
English
•
The following items cannot be registered.
Volume, Balance, Fader, Loudness, Volume offset, Dual
Zone System, Rear Volume
In Standby mode
Firmware version display
Displaying the firmware version with the unit.
1 Select the firmware version display mode
Push the Control knob towards up or down.
Select the "F/W VER" display.
Other than Standby mode
Audio Preset Recall
Recalling the sound setup registered by <Audio
Preset Memory> (page 30).
2 Display the firmware version
Push the Control knob towards right or left.
1 Select the source
Press the [SRC] button.
In Standby mode
2 Enter Menu mode
Demonstration mode Setting
Sets the demonstration mode.
Press the [MENU] button for at least 1 second.
"MENU" is displayed.
3 Select Audio Preset mode
1 Select the Demonstration mode
Push the Control knob towards up or down.
Select the "DEMO" display.
Push the Control knob towards up or down.
Select the "A-PRESET" display.
4 Enter Audio Preset mode
2 Set the Demonstration mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 2 seconds.
Each time you press the knob at least 2 seconds,
the Demonstration mode alternates between the
settings shown in the table below.
5 Select the Audio Preset Recall
Push the Control knob towards up or down.
Select the "RECALL" display.
Display
"DEMO ON"
"DEMO OFF"
Setting
6 Recall the Audio Preset
The Demonstration mode function is ON.
Exit Demonstration mode (Normal mode).
Press the Control knob for at least 2 seconds.
The "RECALL" display blinks 1 time.
7 Exit Audio Preset mode
Press the [MENU] button.
⁄
•
The User memory of <System Q> (page 8) is changed to
the value which was recalled.
•
The source tone memory item of <Audio Control> (page
8) is changed to the value which was recalled by the
selected source.
|
English
31
Basic Operations of remote control
SRC
ATT
VOL
SRC
AT T
VOL
AUD
AUD
FM/AM/+/–
2-ZONE
DIRECT
[0] — [9]
: This button is used when Kenwood Bluetooth
HANDS FREE BOX is connected. For more
information, refer to the instruction manual of
Bluetooth HANDS FREE BOX.
Loading and Replacing the battery
Basic operations
Use two "AA"/ "R6"-size batteries.
Slide the cover while pressing downwards to
remove it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
[VOL] buttons
Adjusts the volume.
[SRC] button
Each time you press the button, the source
alternates.
For the source alternating order refer to <Selecting
the Source> (page 7).
[ATT] button
Turns the volume down quickly.
When the button is pressed again, the volume
returns to the previous level.
2WARNING
•
Store unused batteries out of the reach of children.
Contact a doctor immediately if the battery is
accidentally swallowed.
¤
•
Do not set the remote control in hot places such as on
the dashboard.
|
32
English
Audio Control
In Disc/USB source
[AUD] button
Selects the Audio item to be adjusted.
[4]/ [¢] buttons
Going forwards and backwards between music.
[VOL] buttons
Adjusts the Audio item.
[+]/ [–] buttons
Going forwards and backwards between disc/
folders.
⁄
•
Refer to <Audio Control> (page 8) for the operation
method, such as the procedures for Audio control and
others operations.
[38] button
Each time you press the button, the music is played
or paused.
•
The remote control can only select and adjust the Basic
Audio item. Selecting and adjusting of the Detail Audio
item cannot be done.
[0] — [9] buttons
When in <Direct Music Search> (page 20) and
<Direct Disc Search> (page 20), enters the music/
disc number.
Dual Zone System
[2-ZONE] button
Each time you press the button, "2ZON" of <Audio
Setup> (page 10) is turned ON or OFF.
[5]/ [∞] buttons
Adjusts the volume of the rear channel.
The rear channel activates while the Dual Zone
System is ON.
In Tuner source
[FM]/ [AM] buttons
Selects the band.
Each time you press the [FM] button, the band
alternates between the FM1, FM2, and FM3 bands.
[4]/ [¢] buttons
Tune up or down band.
[0] — [9] buttons
Press buttons [1] — [6] to recall preset stations.
[DIRECT] button
Enters and cancels the <Direct Access Tuning>
(page 14) mode.
[38] button
Enters and cancels the <PTY (Program Type)>
(page 16) mode.
|
English
33
Accessories/ Installation Procedure
Accessories
¤
•
If the power is not turned ON ("PROTECT" is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
If your car is not prepared for this special connection-
system, consult your Kenwood dealer.
Use a commercially available conversion connector if the
connector does not fit in the vehicle connector.
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
If the fuse blows, first make sure that the wires have not
caused a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent short circuits, also do not remove
the caps on the ends of the unconnected wires or the
terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may receive damage or fail
to work if you share the - wires and/or ground them to
any metal part in the car.
1
..........1
•
•
•
•
2
..........2
3
..........1
•
•
Installation Procedure
1. To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
•
•
•
After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
If the console has a lid, make sure to install the unit so
that the faceplate does not hit the lid when closing and
opening.
•
Mount the unit so that the mounting angle is 30° or less.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
If You Want to Connect iPod
iPod
AUDIO OUT
KCA-iP200 (Optional accessory)
•
•
No other optional accessory can be connected because
the USB connector and the AUX input are used for iPod
connection.
Dual Zone System in <Audio Setup> (page 10) will become
unavailable.
|
34
English
Connecting Wires to Terminals
REMO.CONT
Steering remote control (Light Blue/Yellow)
To Kenwood disc changer/
External optional accessory
To connect these leads, refer to the relevant
instruction manuals.
FM/AM antenna input (JASO)
Antenna Cord
Fuse (10A)
Front left output (White)
Front right output (Red)
Rear left output /Sub Woofer left output (White)
Rear right output /Sub Woofer right output (Red)
Wiring harness
(Accessory1)
TEL mute wire (Brown)
Connect to the terminal that is grounded when
either the telephone rings or during conversation.
MUTE
To connect the Kenwood navigation system, consult
your navigation manual.
If no connections are made, do not
let the wire come out from the tab.
Power control/Motor antenna
control wire (Blue/White)
Connect either to the power control terminal
when using the optional power amplifier, or to the
antenna control terminal in the vehicle.
P. C O N T
ANT.CONT
Battery wire (Yellow)
Ignition wire (Red)
See next page
A–7 Pin (Red)
A–4 Pin (Yellow)
Connector A
Connector B
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
|
English
35
Connecting Wires to Terminals
Connector Function Guide
2WARNING
Pin Numbers for Cable Colour
Functions
Connecting the ISO Connector
ISO Connectors
External Power
Connector
The pin arrangement for the ISO connectors depends on
the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
A-4
A-5
A-6
A-7
A-8
Yellow
Battery
Power Control
Dimmer
Ignition (ACC)
Earth (Ground)
Connection
The default connection for the wiring harness is described in
1 below. If the ISO connector pins are set as described in 2
or 3, make the connection as illustrated.
Please be sure to reconnect the cable as shown 2 below to
install this unit to the Volkswagen vehicles etc.
Blue/White
Orange/White
Red
Black
Speaker
Connector
1(Default setting) The A-7 pin (red) of the vehicle’s
ISO connector is linked with the ignition, and the A-
4 pin (yellow) is connected to the constant power
supply.
Ignition cable (Red)
Unit
Battery cable (Yellow)
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
Green/Black
2The A-7 pin (red) of the vehicle’s ISO connector is
connected to the constant power supply, and the
A-4 pin (yellow) is linked to the ignition.
A-7 Pin (Red)
Ignition cable (Red)
Unit
Vehicle
A-4 Pin (Yellow)
Battery cable (Yellow)
3The A-4 pin (yellow) of the vehicle’s ISO connector
is not connected to anything, while the A-7 pin
(red) is connected to the constant power supply
(or both the A-7 (red) and A-4 (yellow) pins are
connected to the constant power supply).
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin (Red)
Vehicle
A-4 Pin (Yellow)
⁄
•
When the connection is made as in 3 above, the unit’s
power will not be linked to the ignition key. For that reason,
always make sure to turn off the unit’s power when the
ignition is turned off.
To link the unit’s power to the ignition, connect the ignition
cable (ACC...red) to a power source that can be turned on
and off with the ignition key.
|
36
English
Installation
Installing the Unit
Firewall or metal support
Screw (M4X8)
(commercially available)
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Self-tapping screw
(commercially available)
Accessory3
Metal mounting strap
(commercially available)
|
English
37
Removing the Unit
Removing the Hard Rubber Frame
(escutcheon)
1 Engage the catch pins on the removal tool 2 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Lock
Catch
Accessory2
2 When the lower level is removed, remove the
upper two locations.
•
The frame can be removed from the top side in the same
manner.
Removing the Unit
1 Refer to the section <Removing the Hard Rubber
Frame> and then remove the hard rubber frame.
Accessory2
2 Remove the Hex-head screw with integral washer
(M4X8) on the back panel.
3 Insert the two removal tools 2 deeply into the
slots on each side, as shown.
4 Lower the removal tool towards the bottom, and
pull out the unit halfway while pressing towards
the inside.
•
Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands,
carefully not to drop it.
|
38
English
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
!
Cannot switch to Aux source.
• AUX is not turned on. ☞ <Built-in Auxiliary input
Setting> (page 30)
• AUX cannot be used when the KCA-iP200 is
connected.
General
? The Touch Sensor Tone doesn’t sound.
✔
The preout jack is being used.
☞
The Touch Sensor Tone can’t be output from the
preout jack.
• Cannot set up the subwoofer.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
• Cannot set up the low pass filter.
• Preout is not set to subwoofer. ☞ <Switching
preout> (page 26)
Tuner source
? Radio reception is poor.
✔
✔
The car antenna is not extended.
• <Subwoofer Output> (page 10) is not set to On.
• The Dual zone function is enabled. ☞ <Audio
Setup> (page 10)
☞
Pull the antenna out all the way.
The antenna control wire is not connected.
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>
(page 35).
!
• Cannot set up the high pass filter.
• Cannot set up the Fader.
The Dual zone function is enabled. ☞ <Audio
Setup> (page 10)
Disc source
? The specified disc does not play, but another one
plays instead.
!
!
Cannot set up the subwoofer phase.
Low pass filter is set to Through. ☞ <Audio Setup>
(page 10)
✔
✔
The specified CD is quite dirty.
Clean the CD.
The disc is loaded in a different slot from that
specified.
☞
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. ☞ <Audio
Setup> (page 10)
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
Try another disc instead.
☞
Audio file source
!
!
No Audio control effect on AUX.
The Dual zone function is enabled. ☞ <Audio
Setup> (page 10)
? The sound skips when an Audio file is being
played.
✔
The media is scratched or dirty.
• Cannot register a security code.
• Cannot set up Display Illumination Control.
<Demonstration mode Setting> (page 31) is not
turned off.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 6).
✔
✔
The audio file is broken or not supported.
Damaged and unsupported files are skipped.
The recording condition is bad.
Record the media again or use another media.
☞
☞
!
!
Cannot play audio files.
<CD Read Setting> (page 30) is set to "2".
USB device source
Cannot File select.
The Random play function is enabled.
? The USB device is not detected.
✔
The USB connector is disconnected.
☞
Connect the connector of the USB device
properly.
? The USB device does not play its audio files.
The USB connector is disconnected.
✔
☞
Connect the connector of the USB device
properly.
|
English
39
Troubleshooting Guide
IN (Blink):
PROTECT:
NA FILE:
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
The messages shown below display your
systems condition.
EJECT:
• No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
• No CD in the unit.
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button. If
the "PROTECT" code does not disappear,
consult your nearest service center.
NO DISC:
TOC ERR:
No disc has been loaded in the disc
magazine.
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
READ ERR:
• The number of files or folders which are
stored in the connected USB device is above
the limitation.
An Audio file is played with a format that this
unit can’t support.
➪ ----
• The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
kenwood.com/usb/. If the error message is
still displayed, initialize the USB device or
use other USB devices.
COPY PRO:
DEMO:
A copy-protected file is played.
➪ ----
The Demonstration mode has been selected.
➪ The <Demonstration mode Setting> (page
31) is ON. Turn it OFF.
NO DVICE:
NA DVICE:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
E-05:
The disc is unreadable.
BLANK:
NO TRACK:
Nothing has been recorded on the MD.
No tracks are recorded on the MD, although it
has a title.
An unsupported USB device is connected.
➪ For the supported USB devices, refer to
<http://www.kenwood.com/usb/>.
NO PANEL:
E-77:
The faceplate of the slave unit being
connected to this unit has been removed.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
"E-77" code does not disappear, consult
your nearest service center.
NO MUSIC/E-15:• The connected USB device contains no
playable audio file.
• Media was played that doesn’t have data
recorded that the unit can play.
E-99:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the "E-99"
code does not disappear, consult your
nearest service center.
USB ERR:
The connected USB device is rated a current
capacity higher than the allowable limit.
➪ Check the USB device with reference to
<http://www.kenwood.com/usb/>.
Some trouble may have occurred to the
connected USB device.
➪ Change the source to any source other
than USB. Remove the USB device.
LOAD:
Discs are being exchanged in the Disc
changer.
iPod ERR:
REMOVE:
Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
READING:
HOLD:
The unit is reading the data on the disc.
The protective circuit in the unit activates
when the temperature inside the automatic
disc changer exceeds 60°C (140°F), stopping
all operation.
➪ Cool down the unit by opening the
windows or turning on the air conditioner.
As the temperature falls below 60°C
(140°F), the disc will start playing again.
The Remove mode has been selected for the
USB device. You can remove the USB device
safely.
|
40
English
Specifications
Specifications subject to change without notice.
WAV signal
FM tuner section
Frequency range (50 kHz space)
: 87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 26dB)
: 0.7 μV /75 Ω
Quieting Sensitivity (S/N = 46dB)
: 1.6 μV /75 Ω
Frequency response ( 3.0 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 65 dB
Selectivity (DIN)( 400 kHz)
: ≥ 80 dB
Stereo separation (1 kHz)
: 35 dB
: Linear-PCM
Audio section
Maximum output power
: 50 W x 4
Output power (DIN 45324, +B=14.4V)
: 30 W x 4
Speaker impedance
: 4 - 8 Ω
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (during disc play)
: 2500 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
MW tuner section
Frequency range (9 kHz space)
: 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
: 25 μV
USB Interface
USB Standard
: USB1.1/ 2.0
File System
LW tuner section
Frequency range
: 153 kHz – 281 kHz
Usable sensitivity (S/N = 20dB)
: 45 μV
: FAT16/ 32
Maximum Supply current
: 500 mA
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
CD player section
AAC decode
Laser diode
: AAC-LC ".m4a" files
: GaAlAs
WAV signal
: Linear-PCM
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 1 Bit
Auxiliary input
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 100 kΩ
Spindle speed
: 1000 – 400 rpm (CLV 2times)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Signal to Noise ratio (1 kHz)
: 105 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 112 x 160 mm
Weight
: 1.60 kg
AAC decode
: AAC-LC ".m4a" files
|
English
41
|