Firmware Update for the DTR-80.2/70.2 and DHC-80.2
We are pleased to offer this firmware update for the best possible performance of your AV Receiver.
A firmware update is now available through the Network or USB connections on the DTR-80.2/70.2 and
DHC-80.2.
The 11/10/10 update addresses the following:
DTR-80.2/70.2 and DHC-80.2
1. Improves the playback of particular wav files
2. Corrects intermittent activation of Auto Power Down function during playback in NET/USB mode
The 10/27/10 update addresses the following:
DTR-80.2/70.2 and DHC-80.2
1. Stabilizes "Now Initializing" process to activate [NET/USB] mode in a busy network;
2. Improves the playback speed of particular VR (Variable Bit Rate) mp3 files.
3. Changes the timing of volume operation start. (thereby avoiding problems of no sound output after power is
turned on from Standby mode with network control enabled).
The 09/17/10 update addresses the following:
DTR-80.2/70.2 and DHC-80.2
1. Improves Audyssey MultEQ XT32 processing.
Please carry out auto speaker setup again by using Audyssey MultEQ XT32 after upgrade.
2. Enhances the operability and display of network/USB-related functions
The latest update includes all prior updates.
We hope you enjoy the improved functionality this update provides to your AV Receiver.
1
How to turn off RIHD
Updating the Firmware via Network
In the Main menu select “ Hardware
Setup”.
1
DTR-70.2, DTR-80.2 and DHC-80.2 allow you to update
firmware using network connection on rear panel.
*
In this procedure, on-screen display may vary
depending on the model.
•
Make sure the AV receiver/controller and TV are
turned on and Ethernet cable is connected to rear
panel of the AV receiver/controller.
Never unplug or turn off the AV receiver/controller
during updating process.
Never plug or unplug an HDMI cable and Ethernet
cable during updating process.
Never unplug the AC power cord during updating
process.
Do not access the AV receiver/controller from PC
during updating process.
It will take about 30 minutes to update the
firmware.
The AV receiver/controller will retain all your
settings after update is finished.
•
•
•
•
•
•
Select “ HDMI”.
2
Before you start
•
•
Check HDMI Control (RIHD) setting. The update
may not be successful if this setting is on.
Turn off the controller device connected via
RS232C and via Ethernet network.
Set “ HDMI Control(RIHD)” to “Off”.
3
•
•
Turn off Zone 2 and Zone 3.
Stop playback of content from Internet radio, iPod,
USB or servers, etc.
3
Update procedure
Select “ Update” and press ENTER.
Updating will begin.
5
Press RECEIVER followed by SETUP on
the remote controller.
1
As the updating progresses, the TV screen may
disappear depending on the program updated.
In this case, you can see the update progress
on the front display of the AV
receiver/controller. The TV screen will
reappear when you finish the update and turn
on the AV receiver/controller.
Main menu will be displayed on TV screen.
Procedures thereafter can also be performed on
the AV receiver/controller by using its
SETUP, arrow, and ENTER buttons.
Go to “ Hardware Setup” menu.
2
3
Go to “ Firmware Update” menu.
Note that the Firmware Update option will be
grayed out about 50 seconds after the AV
receiver/controller is turned on. Please wait.
Message “ Complete!” appears on the front
display of the AV receiver/controller,
indicating that the update has been
completed.
6
7
Select “ via NET” and press ENTER.
4
Using ON/STANDBY on the front panel,
turn off and on the AV receiver/controller.
Do not use ON or STANDBY on the remote
controller.
Congratulations!! Now you have the latest
firmware on the AV receiver/controller.
(Go to the next page for troubleshooting.)
4
Others
Retry the update procedure from the
beginning. If the error persists, please
contact Integra Support (indicated in
the last page) and provide the error
code.
Troubleshooting
Case1:
If “ No Update” is displayed on the front display of the AV
receiver/controller, the firmware has already been updated.
You do not need to do anything further.
Case3:
If an error occurs during updating process, disconnect then
reconnect the AC power cord and try again.
Case2:
Case4:
If an error occurs, “Error!! *-** No media” is displayed on
the front display of the AV receiver/controller.
(Alpha-numeric characters on the front display are denoted
by asterisks.) See the following table and take appropriate
action.
If you do not have a wired connection to the network, please
contact Integra Support.
Errors during update via network
Error Code Description
*10 *20
Ethernet cable is not detected.
Connect the cable properly. See the
instruction manual for the network
connection.
,
*11 *13 *21
Internet connection error.
Check the following items:
,
,
,
*28
¥ Make sure IP address, subnet mask,
gateway address, and DNS server are
configured properly.
¥ Make sure the router is turned on.
¥ Make sure the AV receiver/controller
and the router are connected with
Ethernet cable.
¥ Make sure the setup configuration of the
router is set properly. See the instruction
manual of the router.
¥ If your network allows only one client
connection and there is any other device
already connected, the AV
receiver/controller cannot access the
network. Consult your Internet Service
Provider (ISP).
¥ If your modem does not function as a
router, you will need a router. Depending
on your network, you may need to
configure the proxy server if needed. See
the document provided by your ISP. If
you still cannot access the Internet, DNS
or proxy server may be temporarily
down. Contact your ISP.
5
How to turn off RIHD
Updating the Firmware via USB
In the Main menu select “ Hardware
Setup”.
1
DTR-70.2, DTR-80.2 and DHC-80.2 allow you to update
firmware using a USB storage device.
In this procedure, on-screen display may vary
*
depending on the model.
•
•
•
•
Make sure the AV receiver/controller and TV are
turned on.
Never unplug or turn off the AV receiver/controller
during updating process.
Never plug or unplug an HDMI cable during
updating process.
Never unplug the USB storage device containing
the firmware file and the AC power cord during
updating process.
Select “ HDMI”.
•
•
•
Do not access the AV receiver/controller from PC
during updating process.
It will take about 30 minutes to update the
firmware.
The AV receiver/controller will retain all your
settings after update is finished.
2
Before you start
•
•
Check HDMI Control (RIHD) setting. The update
may not be successful if this setting is on.
Turn off the controller device connected via
RS232C and via Ethernet network.
•
•
Turn off Zone 2 and Zone 3.
Set “ HDMI Control(RIHD)” to “Off”.
3
Stop playback of content from Internet radio, iPod,
USB or servers, etc.
•
If there is any data in the USB storage device,
remove it.
6
Update procedure
Go to “ Firmware Update” menu.
9
Connect a USB storage device to your PC.
1
If there is any data in the USB storage
device, remove it.
Download the firmware file from the
Integra web site. The file name is as
follows:
2
ONKAVR0003_*******.zip
Unzip the downloaded file. The following
three files are created:
ONKAVR0003_*******.of1
ONKAVR0003_*******.of2
Select “via USB” and press ENTER.
ONKAVR0003_*******.of3
10
11
Copy the extracted files to the USB
storage device. Be careful not to copy the
zip file.
3
4
Remove the USB storage device from your
PC and connect it to the USB port on the
AV receiver/controller. When the AV
receiver/controller has two USB ports, you
can use either one.
Make sure the AV receiver/controller
and TV are turned on.
If the AV receiver/controller is in standby
mode, press ON/STANDBY to light up the
front display.
5
6
Select “Update” and press ENTER.
Updating will begin.
As the updating progresses, the TV screen
may disappear depending on the program
updated. In this case, you can see the update
progress on the front display of the AV
receiver/controller. The TV screen will
reappear when you finish the update and turn
on the AV receiver/controller.
Do not turn off the AV receiver/controller
and do not remove the USB storage device
during updating process.
Select the USB input source. “ Now
Initializing” is displayed on the front
display and then the name of the USB
storage device is displayed. It will take 20
to 30 seconds to recognize the USB storage
device.
Press RECEIVER followed by SETUP
on the remote controller.
Main menu will be displayed on TV screen.
Procedures thereafter can also be performed
on the AV receiver/controller by using its
SETUP, arrow, and ENTER buttons.
7
8
Go to “ Hardware Setup” menu.
7
Message “Complete!” appears on the
front display of the AV
receiver/controller, indicating that the
12
update has been completed.
Using ON/STANDBY on the front panel,
turn off the AV receiver/controller and
then remove the USB storage device.
* Do not use ON or STANDBY on the remote
controller.
13
14
Press ON/STANDBY to turn on the AV
receiver/controller.
Congratulations!! Now you have the latest
firmware on the AV receiver/controller.
(Go to the next page for troubleshooting.)
8
Case3:
Troubleshooting
Case1:
If an error occurs during updating process, disconnect then
reconnect the AC power cord and try again.
If “No Update” is displayed on the front display of the
AV receiver/controller, the firmware has already been
updated. You do not need to do anything further.
Onkyo CORPORATION
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 5728540, JAPAN
The Americas
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600
Fax: 201-785-2650
Case2:
If an error occurs, “ Error!! *-** No media” is
displayed on the front display of the AV
receiver/controller. (Alpha-numeric characters on the
front display are denoted by asterisks.) See the
following table and take appropriate action.
Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET
<http://www.okyousa.com/>
Europe
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194
Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
<http://www.eu.onkyo.com/>
China, Hong Kong
ONKYO CHINA LIMITED
Errors during update via USB
Unit 1&12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road,
Kwai Chung, N.T., Hong Kong
Error Code Description
*10 *20
Tel: 852-2429-3118 Fax: 852-2428-9039
<http://www.onkyochina.com/>
USB storage device is not detected.
Make sure the USB flash memory or
USB cable is properly connected to
the USB port. If the USB storage
device has its own power supply, use
it to power the USB storage device.
,
Asia, Oceania, Middle East, Africa
Please contact an INTEGRA distributor referring to Integra
SUPPORT site.
<http://www.intl.onkyo.com/support/local_support/index.html>
*-14
The firmware file is not found in the
root folder of the USB storage device,
or the firmware file is for other
model. Retry download. If the error
persists, please contact Integra
Support (indicated in the last page)
and provide the error code.
Others
Retry the update procedure from the
beginning. If the error persists, please
contact Integra Support (indicated in
the last page) and provide the error
code.
9
10
|